INCLW01 Week 2 Practice Quiz - Internold Networks

Read the question carefully and choose the best answer(s).
Note: This is a mini-quiz of 10 questions per attempt. Always click 'Try Again' to get a new sets of questions.

Enter email to receive results:

Question 1 of 10

Switch SW1 uses its Gigabit 0/1 interface to connect to switch SW2’s Gigabit 0/2 interface. SW2’s Gi0/2 interface is configured with the speed 1000 and duplex full commands. SW1 uses all defaults for interface configuration commands on its Gi0/1 interface. Which of the following are true about the link after it comes up? (Choose two answers.)

The link works at 1000 Mbps (1 Gbps).

The link runs at 1 Gbps, but SW1 uses half-duplex and SW2 uses full duplex.

Both switches use full duplex.

SW1 attempts to run at 10 Mbps because SW2 has effectively disabled IEEE standard autonegotiation.

Question 2 of 10

In the following line taken from a show interfaces fa0/1 command, which of the following are true about the interface? (Choose two answers.)

The speed was definitely configured with the speed 100 interface subcommand.

The duplex was definitely configured with the duplex full interface subcommand.

The duplex might have been configured with the duplex full interface subcommand.

The speed might have been configured with the speed 100 interface subcommand.

Question 3 of 10

Which of the following is required when configuring port security with sticky learning?

All the other answers list required commands.

Enabling port security with the switchport port-security interface subcommand.

Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand.

Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand.

Question 4 of 10

What type of switch memory is used to store the configuration used by the switch when it is up and working?

Bubble

Flash

RAM

NVRAM

ROM

Question 5 of 10

An engineer wants to set up simple password protection with no usernames for some switches in a lab, for the purpose of keeping curious co-workers from logging into the lab switches from their desktop PCs. Which of the following commands would be a useful part of that configuration?

A password password console subcommand

A login vty mode subcommand

A login local vty subcommand

A transport input ssh vty subcommand

Question 6 of 10

In which of the following modes of the CLI could you type the command reload and expect the switch to reboot?

Enable mode

Interface configuration mode

User mode

Global configuration mode

Question 7 of 10

Imagine that you are told that switch 1 is configured with the dynamic auto parameter for trunking on its Fa0/5 interface, which is connected to switch 2. You have to configure switch 2. Which of the following settings for trunking could allow trunking to work? (Choose two answers.)

dynamic auto

dynamic desirable

None of the other answers are correct.

access

Question 8 of 10

The show port-security interface f0/1 command lists a port status of secure-down. Which one of the following answers must be true about this interface at this time?

The show interface status command lists the interface status as connected.

The show interface status command lists the interface status as err-disabled.

The show port-security interface command could list a mode of shutdown or restrict, but not protect.

The show port-security interface command could list a violation counter value of 10.

Question 9 of 10

A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows:

Which of the following answers describe the result of the port security configuration created with these commands? (Choose two answers.)

If a user connects a switch to the cable, prevents multiple devices from sending data through the port.

Prevents unknown devices with unknown MAC addresses from sending data through the switch ports.

Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config.

Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config.

Question 10 of 10

In the following line taken from a show interfaces fa0/1 command, which of the following are true about the interface? (Choose two answers.)

The duplex was definitely configured with the duplex full interface subcommand.

The speed was definitely configured with the speed 100 interface subcommand.

The speed might have been configured with the speed 100 interface subcommand.

The duplex might have been configured with the duplex full interface subcommand.