INCLW01 Week 2 Practice Quiz - Internold Networks

Read the question carefully and choose the best answer(s).
Note: This is a mini-quiz of 10 questions per attempt. Always click 'Try Again' to get a new sets of questions.

Enter email to receive results:

Question 1 of 10

A switch’s port Gi0/1 has been correctly enabled with port security. The configuration sets the violation mode to restrict. A frame that violates the port security policy enters the interface, followed by a frame that does not. Which of the following answers correctly describe what happens in this scenario? (Choose two answers.)

The switch increments the violation counter for Gi0/1 by 1.

The switch puts the interface into an err-disabled state when the first frame arrives.

The switch generates syslog messages about the violating traffic for the first frame.

The switch discards both the first and second frame.

Question 2 of 10

Imagine that you have configured the enable secret command, followed by the enable password command, from the console. You log out of the switch and log back in at the console. Which command defines the password that you had to enter to access privileged mode?

The password command, if it is configured

Neither

enable password

enable secret

Question 3 of 10

Which of the following line subcommands tells a switch to wait until a show command’s output has completed before displaying log messages on the screen?

exec-timeout 0 0

logging synchronous

history size 15

no ip domain-lookup

Question 4 of 10

In a three-tier campus LAN design, which of the following are typically true of the topology design? (Choose two answers.)

The design uses a partial mesh of links between access and distribution switches

The design uses a partial mesh of links between the distribution and core switches

The design uses a full mesh of links between access and distribution switches

The end user and server devices connect directly to distribution layer switches

Question 5 of 10

Which of the following comparisons does a switch make when deciding whether a new MAC address should be added to its MAC address table?

It compares the destination IP address’s ARP cache entry to the bridging, or MAC address, table.

It compares the VLAN ID to the bridging, or MAC address, table.

It compares the unicast source address to the bridging, or MAC address, table.

It compares the unicast destination address to the bridging, or MAC address, table.

Question 6 of 10

A switch user is currently in console line configuration mode. Which of the following would place the user in enable mode? (Choose two answers.)

Using the quit command

Using the exit command once

Using the end command once

Pressing the Ctrl+Z key sequence once

Question 7 of 10

An engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches? (Choose three answers.)

The ip address command in interface configuration mode

The password command in console line configuration mode

The ip address command in global configuration mode

The ip default-gateway command in VLAN configuration mode

The password command in vty line configuration mode

The ip default-gateway command in global configuration mode

Question 8 of 10

A Cisco Catalyst switch connects with its Gigabit0/1 port to an end user’s PC. The end user, thinking the user is helping, manually sets the PC’s OS to use a speed of 1000 Mbps and to use full duplex, and disables the use of autonegotiation. The switch’s G0/1 port has default settings for speed and duplex. What speed and duplex settings will the switch decide to use? (Choose two answers.)

1000 Mbps

Half duplex

Full duplex

10 Mbps

Question 9 of 10

In the following line taken from a show interfaces fa0/1 command, which of the following are true about the interface? (Choose two answers.)

The speed was definitely configured with the speed 100 interface subcommand.

The speed might have been configured with the speed 100 interface subcommand.

The duplex might have been configured with the duplex full interface subcommand.

The duplex was definitely configured with the duplex full interface subcommand.

Question 10 of 10

The show port-security interface f0/1 command lists a port status of secure-down. Which one of the following answers must be true about this interface at this time?

The show interface status command lists the interface status as err-disabled.

The show port-security interface command could list a mode of shutdown or restrict, but not protect.

The show interface status command lists the interface status as connected.

The show port-security interface command could list a violation counter value of 10.